Given the Hex Dump оf MP3 dаtа belоw, whаt is the bitrate оf the file? (Note, just enter the value without units) 13CB:0110 FF FB 62 64 EE 07 B3 30 - 35 C9 41 E6 1A E2 5C 0C 68 F0 13CB:0120 0C 63 6E 0D 29 29 24 A4 - 98 CB C9 6E B1 63 D4 31 8D B8 13CB:0130 64 4E 31 CA C0 F0 1C 38 - C1 9F 93 87 7F FB 07 E9 DB 1F Use the decoding information below: Sign Length (bits) Position (bits) Description A 11 (31-21) Frame sync (all bits must be set) B 2 (20,19) MPEG Audio version ID 00 - MPEG Version 2.5 (later extension of MPEG 2) 01 - reserved 10 - MPEG Version 2 (ISO/IEC 13818-3) 11 - MPEG Version 1 (ISO/IEC 11172-3) Note: MPEG Version 2.5 was added lately to the MPEG 2 standard. It is an extension used for very low bitrate files, allowing the use of lower sampling frequencies. If your decoder does not support this extension, it is recommended for you to use 12 bits for synchronization instead of 11 bits. C 2 (18,17) Layer description 00 - reserved 01 - Layer III 10 - Layer II 11 - Layer I D 1 (16) Protection bit 0 - Protected by CRC (16bit CRC follows header) 1 - Not protected E 4 (15,12) Bitrate index bits V1,L1 V1,L2 V1,L3 V2,L1 V2, L2 & L3 0000 free free free free free 0001 32 32 32 32 8 0010 64 48 40 48 16 0011 96 56 48 56 24 0100 128 64 56 64 32 0101 160 80 64 80 40 0110 192 96 80 96 48 0111 224 112 96 112 56 1000 256 128 112 128 64 1001 288 160 128 144 80 1010 320 192 160 160 96 1011 352 224 192 176 112 1100 384 256 224 192 128 1101 416 320 256 224 144 1110 448 384 320 256 160 1111 bad bad bad bad bad NOTES: All values are in kbps V1 - MPEG Version 1 V2 - MPEG Version 2 and Version 2.5 L1 - Layer I L2 - Layer II L3 - Layer III "free" means free format. The free bitrate must remain constant, an must be lower than the maximum allowed bitrate. Decoders are not required to support decoding of free bitrate streams. "bad" means that the value is unallowed. MPEG files may feature variable bitrate (VBR). Each frame may then be created with a different bitrate. It may be used in all layers. Layer III decoders must support this method. Layer I & II decoders may support it. For Layer II there are some combinations of bitrate and mode which are not allowed. Here is a list of allowed combinations. bitrate single channel stereo intensity stereo dual channel free yes yes yes yes 32 yes no no no 48 yes no no no 56 yes no no no 64 yes yes yes yes 80 yes no no no 96 yes yes yes yes 112 yes yes yes yes 128 yes yes yes yes 160 yes yes yes yes 192 yes yes yes yes 224 no yes yes yes 256 no yes yes yes 320 no yes yes yes 384 no yes yes yes